Release 8.1i ngdbuild I.24
Copyright (c) 1995-2005 Xilinx, Inc.  All rights reserved.

Command Line: ngdbuild -intstyle ise -dd _ngo -nt timestamp -uc
Custom_Libera.ucf -p xc2vp30-ff1152-6 libera_pll.ngc libera_pll.ngd 

Reading NGO file 'C:/DESIGNS/FPGA/Custom_Libera/libera_pll.ngc' ...
Reading module "icon.ngo" ( "icon.ngo" unchanged since last run )...
Loading design module "C:\DESIGNS\FPGA\Custom_Libera\_ngo\icon.ngo"...
ERROR:NgdBuild:76 - File "C:\DESIGNS\FPGA\Custom_Libera\_ngo\icon.ngo" cannot be
   merged into block "i_icon" (TYPE="icon") because one or more pins on the
   block, including pin "control1<35>", were not found in the file.  Please make
   sure that all pins on the instantiated component match pins in the
   lower-level design block (irrespective of case).  If there are bussed pins on
   this block, make sure that the upper-level and lower-level netlists use the
   same bus-naming convention.

Applying constraints in "Custom_Libera.ucf" to the design...
ERROR:NgdBuild:755 - Line 5 in 'Custom_Libera.ucf': Could not find net(s)
   'clk125_npad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 6 in 'Custom_Libera.ucf': Could not find net(s)
   'clk125_ppad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 7 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_clk_ppad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 8 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_clk_npad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 9 in 'Custom_Libera.ucf': Could not find net(s) 'vcxo'
   in the design.  To suppress this error specify the correct net name or remove
   the constraint.  The 'Allow Unmatched LOC Constraints' ISE property can also
   be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 17 in 'Custom_Libera.ucf': Could not find net(s)
   'sys_clk106_en_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 18 in 'Custom_Libera.ucf': Could not find net(s)
   'sys_clk125_en_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 20 in 'Custom_Libera.ucf': Could not find net(s)
   'PostMortem_P_PAD' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 21 in 'Custom_Libera.ucf': Could not find net(s)
   'PostMortem_N_PAD' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 23 in 'Custom_Libera.ucf': Could not find net(s)
   'TRIGGER_N_PAD' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 24 in 'Custom_Libera.ucf': Could not find net(s)
   'TRIGGER_P_PAD' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 26 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_rst_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 27 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_irq_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 28 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_csn_pad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 29 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_wrn_pad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 30 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<2>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 31 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<3>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 32 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<4>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 33 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<5>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 34 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<6>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 35 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<7>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 36 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<8>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 37 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<9>' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 38 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 39 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 40 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 41 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 42 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<14>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 43 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<15>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 44 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<16>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 45 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_adr_pad_i<17>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 46 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 47 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 48 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 49 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 50 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 51 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 52 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 53 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 54 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 55 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 56 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 57 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 58 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 59 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 60 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<14>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 61 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<15>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 62 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<16>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 63 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<17>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 64 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<18>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 65 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<19>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 66 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<20>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 67 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<21>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 68 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<22>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 69 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<23>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 70 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<24>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 71 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<25>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 72 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<26>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 73 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<27>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 74 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<28>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 75 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<29>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 76 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<30>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 77 in 'Custom_Libera.ucf': Could not find net(s)
   'sbc_dat_pad_io<31>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 80 in 'Custom_Libera.ucf': Could not find net(s)
   'lemo_mclk_ppad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 81 in 'Custom_Libera.ucf': Could not find net(s)
   'lemo_mclk_npad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 82 in 'Custom_Libera.ucf': Could not find net(s)
   'lemo_sclk_npad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 83 in 'Custom_Libera.ucf': Could not find net(s)
   'lemo_sclk_ppad_i' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 92 in 'Custom_Libera.ucf': Could not find net(s)
   'fp_led_pad_o' in the design.  To suppress this error specify the correct net
   name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 93 in 'Custom_Libera.ucf': Could not find net(s)
   'bp_led0_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 94 in 'Custom_Libera.ucf': Could not find net(s)
   'bp_led1_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 95 in 'Custom_Libera.ucf': Could not find net(s)
   'bp_led2_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 97 in 'Custom_Libera.ucf': Could not find net(s)
   'ADC_RESET_o' in the design.  To suppress this error specify the correct net
   name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 99 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_func_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 100 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_clk_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 101 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_data_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 102 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_cs_ckm_pad_o' in the design.  To suppress this error specify the correct
   net name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 103 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_cs_adc1_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 104 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_cs_adc2_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 105 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_cs_adc3_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 106 in 'Custom_Libera.ucf': Could not find net(s)
   'spi_cs_adc4_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 112 in 'Custom_Libera.ucf': Could not find net(s)
   'ADC_CLK_A_i' in the design.  To suppress this error specify the correct net
   name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 113 in 'Custom_Libera.ucf': Could not find net(s)
   'ADC_CLK_B_i' in the design.  To suppress this error specify the correct net
   name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 114 in 'Custom_Libera.ucf': Could not find net(s)
   'ADC_CLK_C_i' in the design.  To suppress this error specify the correct net
   name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 115 in 'Custom_Libera.ucf': Could not find net(s)
   'ADC_CLK_D_i' in the design.  To suppress this error specify the correct net
   name or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE
   property can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 118 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 119 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 120 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 121 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 122 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 123 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 124 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 125 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 126 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 127 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 128 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 129 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 130 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 131 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_a_dat_pad_i<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 132 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 133 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 134 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 135 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 136 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 137 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 138 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 139 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 140 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 141 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 142 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 143 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 144 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 145 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_b_dat_pad_i<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 146 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 147 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 148 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 149 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 150 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 151 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 152 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 153 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 154 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 155 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 156 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 157 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 158 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 159 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_c_dat_pad_i<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 160 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 161 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 162 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 163 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 164 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 165 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 166 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 167 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 168 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 169 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 170 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 171 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 172 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 173 in 'Custom_Libera.ucf': Could not find net(s)
   'adc_d_dat_pad_i<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 178 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io*' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 179 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_udqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 180 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_udqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 181 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_ldqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 182 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_ldqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 183 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io*' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 184 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_udqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 185 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_udqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 186 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_ldqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 187 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_ldqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 188 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_bank_pad_o<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 189 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_bank_pad_o<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 190 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_bank_pad_o<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 191 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_bank_pad_o<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 192 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_casn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 193 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_rasn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 194 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_cke_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 195 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_clk_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 196 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_clkn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 197 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_wen_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 198 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_casn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 199 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_cke_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 200 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_clk_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 201 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_clkn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 202 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_rasn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 203 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_wen_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 204 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_ldm_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 205 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_udm_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 206 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_ldqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 207 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_ldqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 208 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_udqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 209 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_udqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 210 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_odt_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 211 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_csn_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 212 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_ldm_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 213 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_udm_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 214 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_ldqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 215 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_ldqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 216 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_udqs_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 217 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_udqsn_pad_io' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 218 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_odt_pad_o' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 219 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 220 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 221 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 222 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 223 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 224 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 225 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 226 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 227 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 228 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 229 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 230 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 231 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_addr_pad_o<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 232 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 233 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 234 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 235 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 236 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 237 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 238 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 239 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 240 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 241 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 242 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 243 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 244 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_addr_pad_o<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 245 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 246 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 247 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 248 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 249 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 250 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 251 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 252 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 253 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 254 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 255 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 256 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 257 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 258 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 259 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<14>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 260 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2high_data_pad_io<15>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 261 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<0>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 262 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<1>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 263 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<2>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 264 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<3>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 265 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<4>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 266 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<5>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 267 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<6>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 268 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<7>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 269 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<8>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 270 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<9>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 271 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<10>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 272 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<11>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 273 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<12>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 274 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<13>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 275 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<14>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 276 in 'Custom_Libera.ucf': Could not find net(s)
   'ddr2low_data_pad_io<15>' in the design.  To suppress this error specify the
   correct net name or remove the constraint.  The 'Allow Unmatched LOC
   Constraints' ISE property can also be set ( -aul switch for command line
   users).
ERROR:NgdBuild:755 - Line 280 in 'Custom_Libera.ucf': Could not find net(s)
   'DIR<0>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 281 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<4>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 282 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<3>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 283 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<2>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 284 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<1>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 285 in 'Custom_Libera.ucf': Could not find net(s)
   'DIR<1>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 286 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<8>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 287 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<7>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 288 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<6>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 289 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<5>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 290 in 'Custom_Libera.ucf': Could not find net(s)
   'DIR<2>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 291 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<12>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 292 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<11>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 293 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<10>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 294 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<9>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 295 in 'Custom_Libera.ucf': Could not find net(s)
   'DIR<3>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 296 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<16>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 297 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<15>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 298 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<14>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 299 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<13>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 300 in 'Custom_Libera.ucf': Could not find net(s)
   'DIR<4>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 301 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<20>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 302 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<19>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 303 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<18>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 304 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<17>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 305 in 'Custom_Libera.ucf': Could not find net(s)
   'DIR<5>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 306 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<24>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 307 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<23>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 308 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<22>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:NgdBuild:755 - Line 309 in 'Custom_Libera.ucf': Could not find net(s)
   'DIO<21>' in the design.  To suppress this error specify the correct net name
   or remove the constraint.  The 'Allow Unmatched LOC Constraints' ISE property
   can also be set ( -aul switch for command line users).
ERROR:Parsers:11 - Encountered unrecognized constraint while parsing.
ERROR:NgdBuild:19 - Errors found while parsing constraint file
   "Custom_Libera.ucf".

Writing NGDBUILD log file "libera_pll.bld"...